DIY No-Sew Passport Cover | inspiredbycharm.com
This post is sponsored by Carnival Cruise Lines.

I don’t know about you, but when I’m traveling with my passport, I’m constantly worried I’ll lose it. It’s such a thin, little book that I never quite know where to put it. I needed something to make it more substantial and easier to spot, and protect it at the same time. My solution: a DIY No-Sew Passport Cover.

DIY No-Sew Passport Cover | inspiredbycharm.com

This cover is simple to make, and it looks chic.

Now I can’t wait to take it with me when my mom and I go on our next Carnival Cruise. We have one scheduled for 2017, and we couldn’t be more excited. I booked us on the new Carnival Vista. (Have you seen the new ship? It looks amazing!)

Since I wasn’t in the mood to drag out my sewing machine for this project, I headed to the store to figure out a way to DIY a passport cover without sewing.

DIY No-Sew Passport Cover | inspiredbycharm.com

Can you tell what I used?

It’s a mend and repair denim patch kit!

DIY No-Sew Passport Cover | inspiredbycharm.com

These kits are available in a variety of denim colors, and they include a couple patches that are the right size for a passport cover. With their adhesive backing, the two patches can be ironed together. The colorful felt in between them creates a cozy and safe pocket for a passport.

DIY No-Sew Passport Cover | inspiredbycharm.com

Inspired by the DIY Felt Cable Organizers I made a couple months ago, I decided to add a snap to ensure the passport stayed inside.

DIY No-Sew Passport Cover | inspiredbycharm.com

Plus, now I have a little matching set of travel accessories.

In 10 minutes or so, you can whip up one of these passport covers too. Let me walk you through the steps.

DIY No-Sew Passport Cover | inspiredbycharm.com

Here’s what you will need:
Mend and repair denim patch kit
12 x 9″ piece of felt
Snap kit
Felt tip marker
Scissors
Hole punch
Iron
Hammer
Passport (as a guide)

For this project, make sure you find a mend and repair denim patch kit that includes two large patches backed with iron-on adhesive.

DIY No-Sew Passport Cover | inspiredbycharm.com

Using one patch as a pattern, trace the shape onto a piece of felt with a felt tip marker. Since you need two of the felt shape, first fold the large piece of felt in half. (This will allow you to cut out both of the shapes at one time.)

DIY No-Sew Passport Cover | inspiredbycharm.com

Next, using your passport as a guide, make three marks on the bottom and sides to show where the passport will sit in your pouch. These marks are necessary so you don’t trim off too much when cutting out the felt.

DIY No-Sew Passport Cover | inspiredbycharm.com

Now you’re ready to cut the felt. The top should be trimmed in line with the pattern you traced. For the sides and the bottom, you’ll want to cut in about a quarter-inch from the line.

As you can see below, doing this allows the adhesive on the sides and bottom of the patches to seal the pouch together. The top will stay open because the felt prevents it from sealing.

DIY No-Sew Passport Cover | inspiredbycharm.com

Next, you’re ready to iron. Stack the patches so that the two sides with the adhesive are together with the felt in between.

DIY No-Sew Passport Cover | inspiredbycharm.com

With your iron on the cotton setting (Do not use steam.), iron each area of the cover for 30-45 seconds. Do this on both sides. Pay special attention to the edges to make sure they are bonded.

DIY No-Sew Passport Cover | inspiredbycharm.com

By ironing, you will seal the edges as well as adhere the denim patches to the felt to create a felt pocket.

DIY No-Sew Passport Cover | inspiredbycharm.com

Next, using a pair of scissors, trim off any overhanging felt or uneven places along the edges of the denim patches.

DIY No-Sew Passport Cover | inspiredbycharm.com

Finally, attach the snaps. Use a hole punch to create a hole in the same spot on both layers of the material in the center about 1/2-inch down from the top. (I recommend inserting your passport into the pouch to find the best spot so your passport will fit when the snaps are closed.

DIY No-Sew Passport Cover | inspiredbycharm.com

When the holes have been made, you’re ready to attach the snaps. (Make sure your kit includes the tools required to attach the snaps.) Follow the instructions on your particular snap kit. This process is simple; just be sure to attach the snaps the correct way so that they will connect when closing your passport cover.

DIY No-Sew Passport Cover | inspiredbycharm.com

 

And with that, your DIY No-Sew Passport Cover is complete!


DIY No-Sew Passport Cover | inspiredbycharm.com

This cover is so cute and practical. Given the variety of colors of denim patches, felt, and snaps that are available today, you can come up with a combination to match your travel gear.

DIY No-Sew Passport Cover | inspiredbycharm.com

Plus, there’s room in the cover to tuck in other things such as cash, credit cards, or even your Carnival Sign and Sail card. (You will use this card for identification and to make purchases on the ship.) When you go on a Carnival cruise, it’s essential that you carry your passport and Sign and Sail Card with you when you exit the ship at any port of call. Having these items in one place is a great way to stay organized.

DIY No-Sew Passport Cover | inspiredbycharm.com

I decided to keep my DIY No-Sew Passport Cover plain on the front, but feel free to add accessories and embellishments. You could even dust off that BeDazzler in your closet. Have fun and make the cover your own.

I hope you enjoyed this DIY. Happy traveling!

This post was created for Away We Go with Carnival, the destination for getting in the getaway state of mind. Head on over.

Comments

  • Matilda Joyce at

    You are so creative!

  • Elle at

    Love this clever idea! Thanks, and happy travels to you and your mom.

  • Debbie at

    Great idea and looks awesome. Will have to remember this one.

  • Julie Blanner at

    I love these! There’s such as chic and easy way to protect your passport.

Post a comment (Need an avatar?)

* required fields